SavvyTanks Setup Guide
SavvyTanks is an add-on to our existing control panels. Designed to be plug and play with minimal setup. Please follow the instructions below to install and configure SavvyTansks to work with your control panel.
Connectivity and Comptable Devices
SavvyTanks is capable of monitoring:
Up to 3 water sensors. These are pre-named 'Fresh', 'Grey' and 'Black. SavvyTanks works with CBE PC200 tank probes, whether purchased from us or elsewhere.
LPG tanks with built in 0-90 or 0-95 ohm sender. We typically see Gasit and Propex underslung tanks been connected but all 0-95 ohm senders are compatible.
Control 12v Gas Isolation Solenoid.
Grey Waster remote drain point.
SavvyTanks connects back to our control panels using Bluetooth so no wiring is required.
Whats in the box?
As we try to keep our device as simple as possible, the only thing in the box is SavvyTanks. You may have ordered additional water sensors to work with your device.
Wiring
Wiring up our device couldn't be simpler. Our module needs only a 12v power supply and to be connected to the sensors of your choice.
Powering the device
To power all of our Add-On's, we simply require a 12v 1a fused supply. As clearly marked on the device, please wire up the 12v supply via the 12v_IN +/- connectors. Please ensure you correctly wire the device, incorrect polarity will damage the unit.
Connecting the Water level Sensors
To connect your CBE PC200 Water sensors, remove the white connector from the sender and extend the cable if needed.
On the Tanks unit you will see Tanks 1 - 3 clearly marked. You can use any of these connections for your water probe however the default configuration is:
Tank 1 - Fresh Water
Tank 2 - Grey Water
Tank 3 - Black water.
This is configurable within the display unit.
Connect your wires as labelled:
White = +
Brown = -
Green - S
Connecting the Gas level Sensor
SavvyTanks will work with any 0-90 or 0-95 ohm sender. The wiring is not polarity specific and so these can be wired up to the GAS screw terminals either way round.
From your Gas sender, you should have 2 wires, simply connect these to SavvyTanks to the connectors labelled GAS.
Connecting the Gas Solenoid
SavvyTanks is capable of controlling a remote gas solenoid for your underslung gas tanks. This is fully tested with Gasit and Propex tanks however works with any 12v solenoid.
To connect your solenoid, connect it to your 12v supply as per the manufactures instructions. To switch the supply from on/off, connect your Negative wire from the solenoid to either NO or NC (See Below) on the relays highlighted. Your ground or Negative wire from the power source should connect to COM.
Each of the relays has 3 connections:
NO (Normally Open) - The default setting is OFF, activating the switch will turn it ON.
COM (Common) - Connect to Ground
NC (Normally Closed) - The default setting is ON, activing the switch with turn if OFF.
Connecting the Remote drain valve
SavvyTanks can connect to a 12v auto return remote drain valve for your water tank.
To connect your 12v operated drain valve. Connect the live wire to your 12v feed as per the manufacturer’s recommendation. Similar to the Gas solenoid, To switch the supply from on/off which will activate the valve, connect your Negative wire from the valve to either NO or NC (See Below) on the relays highlighted.
Your ground or Negative wire from the power source should connect to COM.
Each of the relays has 3 connections:
NO (Normally Open) - The default setting is OFF, activating the switch will turn it ON.
COM (Common) - Connect to Ground
NC (Normally Closed) - The default setting is ON, activing the switch with turn if OFF.
Linking to your SavvyVan Control Panel
To connect to SavvyTanks via Bluetooth using your SavvyVan display, please navigate to settings > Enter your passcode > Bluetooth Devices > Scan for devices.
Your SavvyVan unit will search for nearby Bluetooth devices, please select the Green + next to 'SavvyTanks' as shown below
Now your device is connected, please navigate back to setting then into 'Tank Settings'
Within Tank Settings you can enable the SavvyTanks feature. Once Enabled please select the tanks that you have made the physical connections to. You are then able to configure:
Tank Type - Select the kind of tank you have connected from Fresh, Gray or Black.
Capacity - Select your tanks capacity.
Relay - Select any relays you have connected to. If a relay is selected, when you click on the tank within the tanks page, it will activate the relay.
Using the SavvyTanks
Once configured, you will then see your tank levels on the main screen. If multiple tanks have been selected it will rotate the tanks every 30 seconds. Should a relay attached to the tank be activated then a red circle will show around that tank.
Clicking on the Tank icon will take you to the main tank page where all tanks and their status are visible.
Specifications
Working Voltage 7- 30v
Current draw 0.04a @12v
Dimentions: (L)87mm, (W)72mm, (H)35mm
Disclaimer of Liability
SavvyVan products are designed to provide convenience and safety to users of campervans, motorhomes, and other recreational vehicles. However, improper installation, use, or operation of our products may cause damage to the product itself or other property, or even injury to individuals. Therefore, it is important to read and follow all instructions and safety precautions provided in the installation guide carefully.
SavvyVan and its suppliers shall not be liable for any damage or injury resulting from the installation, use, or operation of its products that is not in accordance with the instructions and safety precautions provided in the installation guide. This includes, but is not limited to, incorrect installation, use or operation of the product, or any modifications made to the product. SavvyVan shall not be liable for any incidental, consequential, or punitive damages arising from the use of its products.
By purchasing and using SavvyVan and its suppliers products, you acknowledge and agree that you assume all responsibility and risk associated with the installation, use, and operation of the product. You further acknowledge and agree to hold SavvyVan and its suppliers harmless and to release it from any liability for any claims, damages, or expenses arising from your installation, use, or operation of its products.
Please contact us if you have any questions or concerns regarding the installation, use, or operation of our products.